• New
    PROX engine bearing 6205 C4 – 25 × 52 × 15 mm for TM RACING EN 125, EN 144, MX 125, MX 144 from 2003 to 2012
    PROX engine bearing 6205 C4 – 25 × 52 × 15 mm for TM RACING EN 125, EN 144, MX 125, MX 144 from 2003 to 2012

    PROX engine bearing 6205 C4 – 25 × 52 × 15 mm for TM RACING EN 125, EN 144, MX 125, MX 144 from 2003 to 2012

    Review (0)
    €14.90
    Tax Included
    Stock del proveedor, enviado en 2 a 5 días.

    Bearing: 6205 C4 – 25 × 52 × 15 mm

    An engine bearing: it lets a shaft (crank, gearbox, pump) turn without friction.

    Quantity :
    In stock

    Stock del proveedor, enviado en 2 a 5 días.

      Check before ordering

      • Bearing: 6205 C4
      • Dimensions (inner × outer × width): 25 × 52 × 15 mm

      PROX offers this engine bearing for TM RACING EN 125, EN 144, MX 125, MX 144 from 2003 to 2012. The engine’s shafts run on ball or roller bearings in the cases. They carry heavy loads at high revs and eventually develop play.

      What is this bearing made of?

      Races and balls (or rollers) in hardened chrome steel, 100Cr6 type: a very hard steel that withstands the fatigue of millions of engine revolutions.

      • Open bearing: unsealed, it is lubricated and cooled by the engine oil; clean oil is its best protection.
      • C3 / C4 internal clearance: slightly more clearance than normal for a hot engine’s expansion; always refit the original clearance.
      • Limit: it dislikes dust and old oil; running short of oil destroys it within minutes.

      Why choose PROX?

      ProX uses Koyo or NTN bearings, largely made in Japan in OEM factories, with the original internal clearance (C3 / C4).

      When should you replace the bearings on your TM RACING MX 125?

      On competition bikes the main bearings are replaced at every bottom-end rebuild, at the hours recommended by the manufacturer. With the cases open, spin each bearing by hand: the slightest rough spot means it must go.

      Specifications and fitting tips

      • Application: Crankshaft
      • ProX bearings are made in major bearing manufacturers' factories, mainly in Japan
      • All bearings are made to OEM specifications for optimum quality and performance

      Cross-Mania tip: Heat the cases to remove and fit the bearings without forcing them, and replace the oil seals at the same time.

      Also needed with this part

      Compatibility

      Check the exact model and year of your bike in the list below before ordering.

      Fits:
      TM RACING EN 125 2012
      TM RACING EN 125 2011
      TM RACING EN 125 2010
      TM RACING EN 125 2009
      TM RACING EN 125 2008
      TM RACING EN 125 2007
      TM RACING EN 125 2006
      TM RACING EN 125 2005
      TM RACING EN 125 2004
      TM RACING EN 144 2012
      TM RACING EN 144 2011
      TM RACING EN 144 2010
      TM RACING EN 144 2009
      TM RACING EN 144 2008
      TM RACING MX 125 2012
      TM RACING MX 125 2011
      TM RACING MX 125 2010
      TM RACING MX 125 2009
      TM RACING MX 125 2008
      TM RACING MX 125 2007
      TM RACING MX 125 2006
      TM RACING MX 125 2005
      TM RACING MX 125 2004
      TM RACING MX 125 2003
      TM RACING MX 144 2012
      TM RACING MX 144 2011
      TM RACING MX 144 2010
      TM RACING MX 144 2009
      TM RACING MX 144 2008

      PROX
      23.6205C4
      1 Item

      Specific References

      No customer reviews for the moment.

      Write your review
      PROX engine bearing 6205 C4 – 25 × 52 × 15 mm for TM RACING EN 125, EN 144, MX 125, MX 144 from 2003 to 2012
      PROX engine bearing for TM RACING EN 125, EN 144, MX 125, MX 144 from 2003 to 2012
      PROX engine bearing 6205 C4 – 25 × 52 × 15 mm for TM RACING EN 125, EN 144, MX 125, MX 144 from 2003 to 2012
      €14.90
      Tax Included