• New
    HOT RODS connecting rod kit for KTM SX-F 250, XC-F 250, HUSQVARNA FC 250 and GAS GAS EC 250 F, MC 250 F from 2016 to 2023
    HOT RODS connecting rod kit for KTM SX-F 250, XC-F 250, HUSQVARNA FC 250 and GAS GAS EC 250 F, MC 250 F from 2016 to 2023

    HOT RODS connecting rod kit for KTM SX-F 250, XC-F 250, HUSQVARNA FC 250 and GAS GAS EC 250 F, MC 250 F from 2016 to 2023

    Review (0)
    €634.90
    Tax Included
    Bajo pedido, plazo confirmado en 24 horas.

    The connecting rod links the piston to the crankshaft: this kit replaces it with its crank pin and bearing for a bottom-end rebuild.

    Quantity :
    On order

    Bajo pedido, plazo confirmado en 24 horas.

      HOT RODS offers this connecting rod kit for KTM SX-F 250, XC-F 250, HUSQVARNA FC 250 and GAS GAS EC 250 F, MC 250 F from 2016 to 2023. The rod passes the piston’s motion to the crankshaft. Its big-end bearing spins at very high revs and eventually develops play.

      Why replace the connecting rod?

      The benefits:

      • Remove the play that causes noise and vibration.
      • Make a high-hours engine reliable again.
      • Cheaper than a complete crankshaft when the flywheels are good.

      Why choose HOT RODS?

      Hot Rods crankshafts come assembled and trued: double-forged 8620 steel rod and hardened crankpin (58-62 HRC), a ready-to-fit bottom-end rebuild.

      When should you replace the connecting rod?

      Unusual vibration, a deep knock that follows engine speed or play in the con-rod: the bottom end needs a rebuild.

      Recommended hours for a bottom-end rebuild (manufacturer recommendation for the KTM SX-F, Husqvarna FC 2016-2022):

      • Racing: every 100 h.
      • Leisure: no KTM figure; have the wear checked at every top-end rebuild.
      • KTM EXC-F, Husqvarna FE 2017-2023: racing: every 70 h.

      Specifications and fitting tips

      • Contents: Connecting Rod, Crank Pin, Crank Pin Plain Bearings
      • Displacement: 250 cm³
      • Material: 8620 steel
      • Engine: 4-stroke
      • Heavy-duty OE replacement connecting rods
      • Certified AISI 8620 steel for superior strength

      Cross-Mania tip: Fitting requires a press and truing the crankshaft with a dial gauge. If you are not equipped, have it done by a workshop.

      Also needed with this part

      Compatibility

      Check the exact model and year of your bike in the list below before ordering.

      Fits:
      GAS GAS EC 250 F 2023
      GAS GAS EC 250 F 2022
      GAS GAS EC 250 F 2021
      GAS GAS MC 250 F 2023
      GAS GAS MC 250 F 2022
      GAS GAS MC 250 F 2021
      HUSQVARNA FC 250 2022
      HUSQVARNA FC 250 2021
      HUSQVARNA FC 250 2020
      HUSQVARNA FC 250 2019
      HUSQVARNA FC 250 2018
      HUSQVARNA FC 250 2017
      HUSQVARNA FC 250 2016
      KTM SX-F 250 2022
      KTM SX-F 250 2021
      KTM SX-F 250 2020
      KTM SX-F 250 2019
      KTM SX-F 250 2018
      KTM SX-F 250 2017
      KTM SX-F 250 2016
      KTM XC-F 250 2017
      KTM XC-F 250 2016
      KTM XC-F 250 I 2022
      KTM XC-F 250 I 2021
      KTM XC-F 250 I 2020
      KTM XC-F 250 I 2019
      KTM XC-F 250 I 2018

      HOT RODS
      HR00175

      Specific References

      No customer reviews for the moment.

      Write your review
      HOT RODS connecting rod kit for KTM SX-F 250, XC-F 250, HUSQVARNA FC 250 and GAS GAS EC 250 F, MC 250 F from 2016 to 2023
      HOT RODS connecting rod kit for KTM SX-F 250, XC-F 250, HUSQVARNA FC 250 and GAS GAS EC 250 F, MC 250 F from 2016 to 2023
      HOT RODS connecting rod kit for KTM SX-F 250, XC-F 250, HUSQVARNA FC 250 and GAS GAS EC 250 F, MC 250 F from 2016 to 2023
      €634.90
      Tax Included