• New
    VINTCO connecting rod kit for HUSQVARNA CR 125, WR 125, XC 125 and HONDA CR 125 R from 1974 to 1987
    VINTCO connecting rod kit for HUSQVARNA CR 125, WR 125, XC 125 and HONDA CR 125 R from 1974 to 1987
    VINTCO connecting rod kit for HUSQVARNA CR 125, WR 125, XC 125 and HONDA CR 125 R from 1974 to 1987

    VINTCO connecting rod kit for HUSQVARNA CR 125, WR 125, XC 125 and HONDA CR 125 R from 1974 to 1987

    Review (0)
    €216.90
    Tax Included
    Last items in stock

    The connecting rod links the piston to the crankshaft: this kit replaces it with its crank pin and bearing for a bottom-end rebuild.

    Quantity :
    In stock

    Last items in stock

      VINTCO offers this connecting rod kit for HUSQVARNA CR 125, WR 125, XC 125 and HONDA CR 125 R from 1974 to 1987. The rod passes the piston’s motion to the crankshaft. Its big-end bearing spins at very high revs and eventually develops play.

      Why replace the connecting rod?

      The benefits:

      • Remove the play that causes noise and vibration.
      • Make a high-hours engine reliable again.
      • Cheaper than a complete crankshaft when the flywheels are good.

      Why choose VINTCO?

      Vintco rods are reinforced forged steel and come with big-end and small-end bearings and washers: a complete rebuild for a vintage two-stroke.

      When should you replace the connecting rod?

      Unusual vibration, a deep knock that follows engine speed or play in the con-rod: the bottom end needs a rebuild.

      The manufacturer publishes no hour interval for this model: have the con-rod play checked at every piston change. Cross-Mania guideline: rebuild the bottom end every 2 to 3 top-end rebuilds.

      Specifications and fitting tips

      • Contents: 1 x Heavy Duty Forged Steel Connecting Rod, 1 x Crank Pin: 9 mm x 20 mm x 48 mm, 1 x Big End Bearing: 20 mm x 26 mm x 12 mm, 1 x Wrist Pin Bearing: 15 mm x 19 mm x 20 mm, 2 x Thrust Washers: 15 mm x 23 mm x 2 mm
      • Material: Forged steel
      • Style: Heavy duty
      • Heavy-duty forged connecting rods for OEM-equal or better fit and performance
      • Improved oil slots for better bearing lubrication

      Cross-Mania tip: Fitting requires a press and truing the crankshaft with a dial gauge. If you are not equipped, have it done by a workshop.

      Also needed with this part

      Compatibility

      Check the exact model and year of your bike in the list below before ordering.

      Fits:
      HONDA CR 125 R 1980
      HUSQVARNA CR 125 1986
      HUSQVARNA CR 125 1985
      HUSQVARNA CR 125 1984
      HUSQVARNA CR 125 1983
      HUSQVARNA CR 125 1982
      HUSQVARNA CR 125 1981
      HUSQVARNA CR 125 1980
      HUSQVARNA CR 125 1979
      HUSQVARNA CR 125 1978
      HUSQVARNA CR 125 1977
      HUSQVARNA CR 125 1976
      HUSQVARNA CR 125 1975
      HUSQVARNA CR 125 1974
      HUSQVARNA WR 125 1987
      HUSQVARNA WR 125 1986
      HUSQVARNA WR 125 1985
      HUSQVARNA WR 125 1984
      HUSQVARNA WR 125 1983
      HUSQVARNA WR 125 1982
      HUSQVARNA WR 125 1981
      HUSQVARNA WR 125 1980
      HUSQVARNA WR 125 1979
      HUSQVARNA WR 125 1978
      HUSQVARNA WR 125 1977
      HUSQVARNA WR 125 1976
      HUSQVARNA WR 125 1975
      HUSQVARNA WR 125 1974
      HUSQVARNA XC 125 1986
      HUSQVARNA XC 125 1985
      HUSQVARNA XC 125 1984

      VINTCO
      KR2022
      3 Items

      Specific References

      No customer reviews for the moment.

      Write your review
      VINTCO connecting rod kit for HUSQVARNA CR 125, WR 125, XC 125 and HONDA CR 125 R from 1974 to 1987
      VINTCO connecting rod kit for HUSQVARNA CR 125, WR 125, XC 125 and HONDA CR 125 R from 1974 to 1987
      VINTCO connecting rod kit for HUSQVARNA CR 125, WR 125, XC 125 and HONDA CR 125 R from 1974 to 1987
      €216.90
      Tax Included