• New
    NTN Crankshaft Bearing 35x80x21mm for YAMAHA XTZ 660 TENERE, YFM 660 GRIZZLY 4WD, YFM 660 RAPTOR 2WD and HONDA XL 500 S
    NTN Crankshaft Bearing 35x80x21mm for YAMAHA XTZ 660 TENERE, YFM 660 GRIZZLY 4WD, YFM 660 RAPTOR 2WD and HONDA XL 500 S

    NTN Crankshaft Bearing 35x80x21mm for YAMAHA XTZ 660 TENERE, YFM 660 GRIZZLY 4WD, YFM 660 RAPTOR 2WD and HONDA XL 500 S

    Review (0)
    €21.94
    Tax Included
    En stock en nuestro proveedor, enviado en 2 a 5 días.

    An engine bearing: it lets a shaft (crank, gearbox, pump) turn without friction.

    Quantity :
    In stock

    En stock en nuestro proveedor, enviado en 2 a 5 días.

      NTN offers this engine bearing for YAMAHA XTZ 660 TENERE, YFM 660 GRIZZLY 4WD, YFM 660 GRIZZLY CAMO 4WD, YFM 660 RAPTOR 2WD, YXR 660 RHINO 4WD and HONDA XL 500 S 1979-2008. The engine’s shafts run on ball or roller bearings in the cases. They carry heavy loads at high revs and eventually develop play.

      What is this bearing made of?

      Races and balls (or rollers) in hardened chrome steel, 100Cr6 type: a very hard steel that withstands the fatigue of millions of engine revolutions.

      • Open bearing: unsealed, it is lubricated and cooled by the engine oil; clean oil is its best protection.
      • C3 / C4 internal clearance: slightly more clearance than normal for a hot engine’s expansion; always refit the original clearance.
      • Limit: it dislikes dust and old oil; running short of oil destroys it within minutes.

      Why choose NTN?

      NTN, the Japanese bearing maker founded in 1918, is the brand chosen by engine specialists such as ProX for their crankshaft bearing kits.

      When should you replace the bearings?

      On competition bikes the main bearings are replaced at every bottom-end rebuild, at the hours recommended by the manufacturer. With the cases open, spin each bearing by hand: the slightest rough spot means it must go.

      Specifications and fitting tips

      • Manufacturer part number: 6307C3

      Cross-Mania tip: Heat the cases to remove and fit the bearings without forcing them, and replace the oil seals at the same time.

      Also needed with this part

      Compatibility

      Check the exact model and year of your bike in the list below before ordering.

      Fits:
      HONDA XL 500 S 1981
      HONDA XL 500 S 1980
      HONDA XL 500 S 1979
      YAMAHA XTZ 660 TENERE 1996
      YAMAHA XTZ 660 TENERE 1995
      YAMAHA XTZ 660 TENERE 1994
      YAMAHA XTZ 660 TENERE 1993
      YAMAHA XTZ 660 TENERE 1992
      YAMAHA XTZ 660 TENERE 1991
      YAMAHA YFM 660 GRIZZLY 4WD 2008
      YAMAHA YFM 660 GRIZZLY 4WD 2007
      YAMAHA YFM 660 GRIZZLY 4WD 2006
      YAMAHA YFM 660 GRIZZLY 4WD 2005
      YAMAHA YFM 660 GRIZZLY 4WD 2004
      YAMAHA YFM 660 GRIZZLY 4WD 2003
      YAMAHA YFM 660 GRIZZLY 4WD 2002
      YAMAHA YFM 660 GRIZZLY CAMO 4WD 2008
      YAMAHA YFM 660 GRIZZLY CAMO 4WD 2007
      YAMAHA YFM 660 GRIZZLY CAMO 4WD 2006
      YAMAHA YFM 660 GRIZZLY CAMO 4WD 2005
      YAMAHA YFM 660 RAPTOR 2WD 2005
      YAMAHA YFM 660 RAPTOR 2WD 2004
      YAMAHA YFM 660 RAPTOR 2WD 2003
      YAMAHA YFM 660 RAPTOR 2WD 2002
      YAMAHA YFM 660 RAPTOR 2WD 2001
      YAMAHA YXR 660 RHINO 4WD 2007
      YAMAHA YXR 660 RHINO 4WD 2006
      YAMAHA YXR 660 RHINO 4WD 2005
      YAMAHA YXR 660 RHINO 4WD 2004

      NTN
      6307C3
      3 Items

      Specific References

      No customer reviews for the moment.

      Write your review
      NTN Crankshaft Bearing 35x80x21mm for YAMAHA XTZ 660 TENERE, YFM 660 GRIZZLY 4WD, YFM 660 RAPTOR 2WD and HONDA XL 500 S
      NTN Crankshaft Bearing 35x80x21mm for YAMAHA XTZ 660 TENERE, YFM 660 GRIZZLY 4WD, YFM 660 RAPTOR 2WD and HONDA XL 500 S
      NTN Crankshaft Bearing 35x80x21mm for YAMAHA XTZ 660 TENERE, YFM 660 GRIZZLY 4WD, YFM 660 RAPTOR 2WD and HONDA XL 500 S
      €21.94
      Tax Included