• New
    HOT RODS Balancer Shaft Reconditioning Kit for HONDA TRX 450 R SPORTRAX ELECTRIC START 2WD, TRX 450 R SPORTRAX KICK START 2WD
    HOT RODS Balancer Shaft Reconditioning Kit for HONDA TRX 450 R SPORTRAX ELECTRIC START 2WD, TRX 450 R SPORTRAX KICK START 2WD
    HOT RODS Balancer Shaft Reconditioning Kit for HONDA TRX 450 R SPORTRAX ELECTRIC START 2WD, TRX 450 R SPORTRAX KICK START 2WD

    HOT RODS Balancer Shaft Reconditioning Kit for HONDA TRX 450 R SPORTRAX ELECTRIC START 2WD, TRX 450 R SPORTRAX KICK START 2WD

    Review (0)
    €17.90
    Tax Included
    Last items in stock

    An engine bearing: it lets a shaft (crank, gearbox, pump) turn without friction.

    Quantity :
    In stock

    Last items in stock

      HOT RODS offers this engine bearing for HONDA TRX 450 R SPORTRAX ELECTRIC START 2WD, TRX 450 R SPORTRAX KICK START 2WD 2004-2014. The engine’s shafts run on ball or roller bearings in the cases. They carry heavy loads at high revs and eventually develop play.

      What is this bearing made of?

      Races and balls (or rollers) in hardened chrome steel, 100Cr6 type: a very hard steel that withstands the fatigue of millions of engine revolutions.

      • Open bearing: unsealed, it is lubricated and cooled by the engine oil; clean oil is its best protection.
      • C3 / C4 internal clearance: slightly more clearance than normal for a hot engine’s expansion; always refit the original clearance.
      • Limit: it dislikes dust and old oil; running short of oil destroys it within minutes.

      Why choose HOT RODS?

      Hot Rods, the bottom-end specialist since 1993: crankshafts, rods, bearings and seals for a complete rebuild.

      When should you replace the bearings on your HONDA TRX 450 R SPORTRAX ELECTRIC START 2WD?

      On competition bikes the main bearings are replaced at every bottom-end rebuild, at the hours recommended by the manufacturer. With the cases open, spin each bearing by hand: the slightest rough spot means it must go.

      Specifications and fitting tips

      • Manufacturer part number: BBK0005

      Cross-Mania tip: Heat the cases to remove and fit the bearings without forcing them, and replace the oil seals at the same time.

      Also needed with this part

      Compatibility

      Check the exact model and year of your bike in the list below before ordering.

      Fits:
      HONDA TRX 450 R SPORTRAX ELECTRIC START 2WD 2014
      HONDA TRX 450 R SPORTRAX ELECTRIC START 2WD 2013
      HONDA TRX 450 R SPORTRAX ELECTRIC START 2WD 2012
      HONDA TRX 450 R SPORTRAX ELECTRIC START 2WD 2011
      HONDA TRX 450 R SPORTRAX ELECTRIC START 2WD 2010
      HONDA TRX 450 R SPORTRAX ELECTRIC START 2WD 2009
      HONDA TRX 450 R SPORTRAX ELECTRIC START 2WD 2008
      HONDA TRX 450 R SPORTRAX ELECTRIC START 2WD 2007
      HONDA TRX 450 R SPORTRAX ELECTRIC START 2WD 2006
      HONDA TRX 450 R SPORTRAX KICK START 2WD 2009
      HONDA TRX 450 R SPORTRAX KICK START 2WD 2008
      HONDA TRX 450 R SPORTRAX KICK START 2WD 2007
      HONDA TRX 450 R SPORTRAX KICK START 2WD 2006
      HONDA TRX 450 R SPORTRAX KICK START 2WD 2005
      HONDA TRX 450 R SPORTRAX KICK START 2WD 2004

      HOT RODS
      BBK0005
      3 Items

      Specific References

      No customer reviews for the moment.

      Write your review
      HOT RODS Balancer Shaft Reconditioning Kit for HONDA TRX 450 R SPORTRAX ELECTRIC START 2WD, TRX 450 R SPORTRAX KICK START 2WD
      HOT RODS Balancer Shaft Reconditioning Kit for HONDA TRX 450 R SPORTRAX ELECTRIC START 2WD, TRX 450 R SPORTRAX KICK START 2WD
      HOT RODS Balancer Shaft Reconditioning Kit for HONDA TRX 450 R SPORTRAX ELECTRIC START 2WD, TRX 450 R SPORTRAX KICK START 2WD
      €17.90
      Tax Included