• New
    Upper a-arm bearing KIT for KFX700 v-force 2004-08 PIVOT WORKS for KAWASAKI KVF 650 BRUTE FORCE I 4WD, KVF 750 BRUTE FORCE I 4WD
    Upper a-arm bearing KIT for KFX700 v-force 2004-08 PIVOT WORKS for KAWASAKI KVF 650 BRUTE FORCE I 4WD, KVF 750 BRUTE FORCE I 4WD

    Upper a-arm bearing KIT for KFX700 v-force 2004-08 PIVOT WORKS for KAWASAKI KVF 650 BRUTE FORCE I 4WD, KVF 750 BRUTE FORCE I 4WD

    Review (0)
    €99.90
    Tax Included
    Last items in stock

    An engine bearing: it lets a shaft (crank, gearbox, pump) turn without friction.

    Quantity :
    In stock

    Last items in stock

    Wishlist
    Write your review

      PIVOT WORKS offers this engine bearing for KAWASAKI KVF 650 BRUTE FORCE I 4WD, KVF 750 BRUTE FORCE I 4WD 2005-2013. The engine’s shafts run on ball or roller bearings in the cases. They carry heavy loads at high revs and eventually develop play.

      What is this bearing made of?

      Races and balls (or rollers) in hardened chrome steel, 100Cr6 type: a very hard steel that withstands the fatigue of millions of engine revolutions.

      • Open bearing: unsealed, it is lubricated and cooled by the engine oil; clean oil is its best protection.
      • C3 / C4 internal clearance: slightly more clearance than normal for a hot engine’s expansion; always refit the original clearance.
      • Limit: it dislikes dust and old oil; running short of oil destroys it within minutes.

      Why choose PIVOT WORKS?

      Pivot Works kits, sold by the American All Balls Racing group, use hardened NTN, NSK or Koyo bearings from original-equipment bearing suppliers, supplied pre-greased with their seals; every kit carries the Pivot Works limited lifetime warranty.

      When should you replace the bearings on your KAWASAKI KVF 750 BRUTE FORCE I 4WD?

      On competition bikes the main bearings are replaced at every bottom-end rebuild, at the hours recommended by the manufacturer. With the cases open, spin each bearing by hand: the slightest rough spot means it must go.

      Specifications and fitting tips

      • Manufacturer part number: PWAAK-K01-700U

      Cross-Mania tip: Heat the cases to remove and fit the bearings without forcing them, and replace the oil seals at the same time.

      Also needed with this part

      Compatibility

      Check the exact model and year of your bike in the list below before ordering.

      Fits:
      KAWASAKI KVF 650 BRUTE FORCE I 4WD 2013
      KAWASAKI KVF 650 BRUTE FORCE I 4WD 2012
      KAWASAKI KVF 750 BRUTE FORCE I 4WD 2011
      KAWASAKI KVF 750 BRUTE FORCE I 4WD 2010
      KAWASAKI KVF 750 BRUTE FORCE I 4WD 2009
      KAWASAKI KVF 750 BRUTE FORCE I 4WD 2008
      KAWASAKI KVF 750 BRUTE FORCE I 4WD 2007
      KAWASAKI KVF 750 BRUTE FORCE I 4WD 2006
      KAWASAKI KVF 750 BRUTE FORCE I 4WD 2005

      PIVOT WORKS
      PWAAK-K01-700U
      2 Items

      Specific References

      Write your review

      No customer reviews for the moment.

      Write your review
      Upper a-arm bearing KIT for KFX700 v-force 2004-08 PIVOT WORKS for KAWASAKI KVF 650 BRUTE FORCE I 4WD, KVF 750 BRUTE FORCE I 4WD
      Upper a-arm bearing KIT for KFX700 v-force 2004-08 PIVOT WORKS for KAWASAKI KVF 650 BRUTE FORCE I 4WD, KVF 750 BRUTE FORCE I 4WD
      Upper a-arm bearing KIT for KFX700 v-force 2004-08 PIVOT WORKS for KAWASAKI KVF 650 BRUTE FORCE I 4WD, KVF 750 BRUTE FORCE I 4WD
      Upper a-arm bearing KIT for KFX700 v-force 2004-08 PIVOT WORKS for KAWASAKI KVF 650 BRUTE FORCE I 4WD, KVF 750 BRUTE FORCE I 4WD
      €99.90
      Tax Included